По основному авт.св. О 74866 известно устройство дл автоматической подачи электрода-инструмента электроискрового станка. Предлагаемое устройство отличаетс тем, что применен двигатель дл автоматического управлени величиной.пода чи инструмента. Скорость двигател ре гулируетс автоматически. Дл включе ни. и выключени регул тора скорости служит треть магнитна муфта, обмотк которой св зана с электрической схемой станка. На чертеже показана схема предлагаемого устройства. Электродвигатель 1, питаемый от постороннего источника тока, регулируетс реостатом 2 автоматически и вручную и через систему передач приводит в холостое вращение в разные стороны электромагнитные муфты 3 и 4 Муфта 4, питаема от постороннего ис точника тока, осуществл ет подачу ин струмента. Электромагнит муфты 4 в два раза слабее электромагнита муфты 3 обратного хода, питаемой от цепи электроискровой схемы. В начальный момент муфта 4 прит гивает диск 5, сид щий на скольз щей лпонке, и приводит в движение ходовой винт 6,. двигающий электрод-инструмент. Прикосновение инструмента к .детали создает длительное короткое замыкание. В этот момент муфта 3 сообщает инструменту обратный ход, а муфта 7 включает регул тор скорости двигател . Во врем длительного короткого замыкани регул тор срабатывает и поворачивает шестерню 8, котора враща сь, передвигает движок реостата двигател , убавл его скорость. Инструмент, получив обратное движение, размыкает цепь, срабатывает муфта 4 и инструмент уже с меньшей подачей идет к детали. Если при движении инструмента зазор все врем посто нен, то процесс идет нормально , если подача еще велика, то оп ть произойдет длительное короткое залвлкание и все повторитс , пока |Не установитс нормальна подача, о которой суд т по устойчивьлм показани м вольтметра,. Така схема позвол ет сразу устанавливать нужный дл данного станка режим, мину промежуточные настройки. После установлени стабильного заэора в процессе обработки происход тAccording to the main auth. About 74866 a device is known for automatically feeding an electrode-tool of an electric-spark machine. The proposed device is characterized in that a motor is used to automatically control the value of the tool supply. Engine speed is automatically adjusted. To turn it on. and turning off the speed controller serves a third magnetic coupling, the winding of which is associated with the electrical circuit of the machine. The drawing shows a diagram of the proposed device. The electric motor 1, powered by an external power source, is controlled by the rheostat 2 automatically and manually and through an gearing system causes electromagnetic idlers 3 and 4 to idle rotation in different directions. Clutch 4, powered by an external power source, feeds the tool. The clutch 4 electromagnet is two times weaker than the reverse clutch electromagnet 3 fed from the electric-spark circuit. At the initial moment, the clutch 4 attracts the disk 5, which sits on the sliding lip, and drives the lead screw 6 ,. moving electrode tool. Touching the tool to. Parts creates a long short circuit. At this point, clutch 3 tells the tool to reverse, and clutch 7 turns on the engine speed regulator. During a prolonged short circuit, the controller triggers and turns gear 8, which rotates, moves the engine of the engine rheostat, and decreases its speed. The tool, having received a reverse movement, opens the circuit, clutch 4 is activated and the tool goes to the part with a smaller feed. If the gap is constant all the time when the tool is moving, then the process proceeds normally, if the flow is still large, then a long short talk will occur again and everything will repeat until | the flow is normal, as judged by the stability of the voltmeter. This scheme allows you to immediately set the desired mode for the machine, min intermediate settings. After establishing a stable surplus during processing
кратковременные замыкани и в этот момент муфта 3 сообщает инструменту незначительный обратный ход или остановку , муфта. 7 приводит во вращение барабан 9. Если замыкание кратковременно, то барабан 9 сделает один-три оборота, short-term closures and at this point clutch 3 gives the tool a slight reverse or stop clutch. 7 causes the rotation of the drum 9. If the circuit is short, then the drum 9 will make one to three turns,
Дл срабатывани автомата необходимо , чтобы барабан сделал не менее четырех оборотов. При прекращении замыкани автомат отключаетс и под действием груза 10 барабан 9 делает два оборота в обратном направлении. Таким образом , сколько бы ни повтор лось кратковременных коротких замыканий с определенным интервалом, регул тор скороети не реагирует на положение движкаTo operate the machine, it is necessary for the drum to make at least four turns. When the closure is stopped, the machine is turned off and under the action of the load 10 the drum 9 makes two turns in the opposite direction. Thus, no matter how many short-term short circuits recur at a certain interval, the network controller does not respond to the position of the engine.
реостата.rheostat.