Wydobywanie ropy z otworów wiertni¬ czych „tlokowaniem" polaczone jest ze strata czasu, gdyz nie odbywa sie jedno¬ stajnie. Mianowicie ropa wyplywa tylko podczas wyciagania tloka, zas wpuszcze¬ nie go do otworu wymaga pewnego czasu, stosownie do glebokosci, a ten czas jest o- czywiscie stracony. Pompowanie z wiek¬ szych glebokosci, zapomoca zwyklej pom¬ py — a nawet z mniejszych glebokosci tam, gdzie ropa zawiera duzo parafiny, o- kazalo sie niemozebne, bowiem ssanie pompa obniza temperature, a wskutek te¬ go parafina krzepnie i zatyka wentyle. Ce¬ lem wiec pewnego i jednostajnego wydo¬ bywania ropy stosuje sie w ostatnim cza¬ sie pompy smoezkowe.Rodzaj takiej pompy przedstawia zala¬ czony rysunek, a rózni sie ona od dotych¬ czas znanych glównie tern, ze rura dopro¬ wadzajaca sprezone powietrze, nie jest u- •mieszczona centrycznie okolo rury do wyplywu ropy, ale obok niej, wskutek cze¬ go srednica jednej i drugiej moze byc mniejsza, a wiec i koszt mniejszy.Fig. 1 przedstawia przekrój podluzny o- tworu wiertniczego i obie rury w polacze¬ niu ze soba; fig. 2 — urzadzenie smoczko¬ we i fig. 3 — przekrój poprzeczny po linji A — B.Rura 1, która sie wprowadza do otworu wiertniczego tak gleboko, aby koniec jej, wzglednie najnizszy smoczek zanurzyl sie w ropie, sluzy do odprowadzania tej ostat¬ niej nazewnatrz. W rurze tej wstawione sa w pewnych odstepach (30 do 40 m) smoczki 2 z bocznemi, rurowemi odsadka- mi 3 (fig. 2, 3), do których przykreca sie, w miare zaglebiania przewodu 1, rury 4.Rury te sluza do wpuszczania sprezonegopowietrza pod cisnieniem okolo 8 atmosfer.Urzadzenie smoczkowe sklada sie z trzech dysz 5, 6, 7, celem silniejszego wsysania powietrza z przewodu rurowego 1, wsku¬ tek czego ropa podnosi sie w nim coraz wyzej, az do góry otworu wiertniczego i wreszcie wyplywa nazewnatrz. Poniewaz oba przewody nie sa umieszczone cen- trycznie, jak przy dotychczasowych urza¬ dzeniach, t. j. przewód do odprowadzania ropy w przewodzie do tloczenia sprezone¬ go powietrza, ale obok siebie, wiec sredni¬ ca tego ostatniego jest znacznie mniejsza, a zatem i koszt urzadzenia mniejszy.Jezeli otwór wiertniczy zarurowany jest od góry do dolu jednem pasmem rur her¬ metycznych 8, to zastosowanie przewodu 4 moze zupelnie odpasc, a wtedy nalezy tylko otwór w górze hermetycznie zamknac i przez to zamkniecie wprowadzac sprezo¬ ne powietrze. PLExtracting oil from the boreholes by "pistoning" is a waste of time, as it is not done consistently. Namely, the oil flows only when the piston is pulled, and it takes a certain time to insert it into the hole, depending on the depth, and this time is actually lost. ”Pumping from greater depths, with the help of a normal pump - and even from shallower depths, where the oil contains a lot of paraffin, was impossible, because the suction pump lowers the temperature and thus the paraffin It clots and clogs the valves. Therefore, in order to ensure a steady and steady extraction of oil, pusher pumps have recently been used. The type of pump is shown in the attached figure, and it differs from previously known mainly that the pipe is The compressed air supply is not centrally located around the oil discharge pipe but next to it, as a result of which the diameter of both may be smaller and hence the cost lower. Fig. 1 shows the cross-section p. a slack drill bit and both pipes connected to each other; Fig. 2 - nipple device and Fig. 3 - cross section along line A-B. Tube 1, which is inserted into the borehole so deep that the end of its relatively low nipple sinks into the oil, serves to drain the latter ¬ later on outside. In this pipe, at certain intervals (30 to 40 m), nipples 2 with lateral, tubular offsets 3 (Figs. 2, 3) are inserted, to which the pipes 4 are screwed, as the pipe 1 is embedded in them. The nipple device consists of three nozzles 5, 6, 7, in order to suck air more strongly from the conduit 1, so that the oil rises higher and higher in it, up to the top of the borehole and finally flows out outside. Since the two lines are not placed centrally as with the existing devices, i.e. the oil discharge line in the compressed air line, but next to each other, the diameter of the latter is much lower, and therefore the cost of the device If the borehole is tubed from the top to the bottom with one strip of hermetic pipes 8, the use of the conduit 4 may completely fall off, and then only the opening at the top should be hermetically sealed and thus closed with compressed air. PL